The Smart Resetter for Epson will reset the "smart chip" on almost all Epson inkjet cartridges multiple times. Reset printer cartridge chips to factory specifications, showing full ink levels and providing the same number of cycles as when the Epson inkjet cartridge was new. Just place the cartridge on the resetter and wait 4 seconds!
http://reset-epson-resetter.blogspot.com
Epson Resetter
Why use the Epson Resetter
Epson inkjet cartridges with "smart chips" send a signal to the printer when empty, and the printer won't recognize the refilled cartridge as it "remembers" it as empty. The resetter will "reset" the Epson chips to "full" specs.
Which Epson Resetter?
* Epson Resetter V1.0: For Epson inkjet cartridges with 7-pin chips
* Epson Resetter V2.0: For Epson plotter (wide format) cartridges with 7-pin chips
* Epson Resetter V3.0: For Epson inkjet cartridges with 9-pin chips (also backwards compatible with V1.0)
http://epsonresetter.co.cc
Alternatives to the Canon Resetter
- Compatible Chips: Another method to overcome the "out of ink" signal that is sent to the printer due to a spent inkjet cartridge is to replace the chip. Compatible chips are available on request.
Note: Images and instructions are property of Uni-Kit, an Easy Group brand and are protected by copyright laws
- Compatible Cartridges (with chips): Uni-Kit offers compatible or remanufactured Canon CLI-8 and PGI-5 cartridges with new, compatible chips.
- Manual overide procedure: Although this procedure may not work for all Canon printers, it is an option for customers to consider:
- Place the refilled cartridge (with the original "empty" chip) in the printer
- Press and hold the Reset/OK Button for 5 seconds to reset the chips.
- The "Ink Low" dialog box will pop up (similar to photo 1 below)
- Continue to print until the "ink has run out" dialog box pops up (similar to photo 2 Below) Click "OK" to continue to print.
- The "Ink Low" dialog box may reappear, if so repeat the first 2 steps
- Then the "once empty" dialog box will pop up (similar to photo 3 Below) Click "Yes" to continue to print
- The "Not Liable" dialog box will pop up (similar to photo 4 below). Click "Yes" to continue to print
- Continue to print until the "remaining level of ink" dialog box pops up (similar to photo 5 Below) Click "OK" to continue to print
- Another dialog box will pop up with the "press and hold the Resume" or "press and hold the Paper Feed" button (similar to photo 6). Press and hold the "STOP/RESET" button (for Canon MP Series) or "PAPER FEED" button (for Canon IP Series) for 5 seconds. DO NOT Click "Back" or "Cancel Printing"
- The "Ink Monitor" dialog box will appear and the printer will continue to print. (similar to photo 7) In the event that that the "press and hold the Resume " dialog box pops up again, Press and hold the Paper Feed Button or Stop/Reset Button for 5 seconds
Why use the Canon Resetter
Canon CLI8 and PGI5 inkjet cartridges with "smart chips" send a signal to the printer when empty, and the printer won't recognize the refilled cartridge as it "remembers" it as empty. The resetter will "reset" the Canon chips to "full" specs.
Continue reading..
Canon MPC190 Reset Waste Ink
Canon MPC190 ResetWaste Ink 1) Enter SERVICE MODE.
By pressing Menu, Copy, Scan,Copy,Copy
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [Set] key.
7) Press the [Stop/Reset] key (returningto the state of 3)), and then press the [ON/OFF]key.
Canon S9000 reset
CanonS9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMAiP3000 above,
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.
CanonBJ F900, F890, F700, F500, S900, S820, S750 and S520
CanonBJ F900, F890, F700, F500, S900, S820, S750 and S520
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button.
Release the RESUME button, then press and release the RESUME buttontwo more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. service/factory test print out, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change,and return to the top of the function selection menu. Pressing thePOWER button again turns off the printer for a rest
CanonBJ-30 BJC-35v BJC-70 F14 Error Reset
CanonBJ-30 BJC-35v BJC-70 F14 Error Reset
1: Unplug adapter
2: Hold POWER
3: Plug in ADAPTER
4: Release POWER after printer starts
5: Hold FF and MENU and press POWER
6: Release after beeps
7: Press <> Cartridge until 1A is displayed
8: Press ONLINE
9: Press POWER to shut off printer
10: Unplug printer then re-plug printer
CanonBJC-50 BJC-55 BJC-80 BJC-85 M40 M70
CanonBJC-50 BJC-55 BJC-80 BJC-85 M40 M70
1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beeps
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord
CanonBJC-600 BJC-600e BJC-610 BJC-620
CanonBJC-600 BJC-600e BJC-610 BJC-620
1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps
Canon BJC-3000
Canon BJC-3000 BJC-6000BJC-6100 BJC-6200 S400 S450 F300 F600 F620CanonBJC-7000 BJC-7100BJC-8000 BJ-F800 i6500
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three (3) times.The indicator should be orange.
6: Press Power to set data
CanonBJC-5100Self Test
CanonBJC-5100Self Test
Switch Printer off. Hold Power for 1 beep.
Waste Counter Reset
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four (4) times.The indicator should be GREEN.
6: Press Power to set dataService Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two (2) times.The indicator should be GREEN.
6: Press Power to Print Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
CanonBJC-5000 reset
CanonBJC-5000
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four (4) times.The indicator should be GREEN.
6: Press Power to set data Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two (2) times.The indicator should be GREEN.
6: Press Power to Print Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
CanonBJC-210 BJC-240BJC-250 BJC-255 BJC-265CanonBJC-4100 BJC-4200BJC-4300 BJC-4400 BJC-4550 BJC-4650
CanonBJC-210 BJC-240BJC-250 BJC-255 BJC-265CanonBJC-4100 BJC-4200BJC-4300 BJC-4400 BJC-4550 BJC-4650
1. Unplug Power Cord
2. Hold POWER and RESUME buttons
3. Plug in Power Cord
4. Release buttons
5. Open front door of printer
6. Hold the CARTRIDGE and RESUME buttons
7. Press POWER
8. Release all buttons after the beeps
9. Press CARTRIDGE once
10. Press RESUME
Reset CanonBJC-2000 BJC-2100 Series
CanonBJC-2000 BJC-2100 Series
1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel
3: Hold down the RESUME/RESET button and plug in the AC power cord
4: Release RESUME/RESET after plugging in the AC Power cord.
5: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET.
6: Press and HOLD RESUME/RESET for two seconds or more and release it.
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Unplug AC Power Cord to set data.
CanonBJC 1000 Series reset
CanonBJC 1000 Series
1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.
CanonS450 Printer
CanonS450 Printer
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5. Release Power button
6: When the indicator lights steady, press RESUME three(3) times.The indicator should be orange.
7: Press Power to set data
Canon PIXMA iP1500 Waste Ink Counter Reset.
Step1: Manual for Service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
Step 2 : Softwarefor Permanent
1. Reconnect the printer cable.
2. OpenGeneral Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.
Remark"After service mode Pls use software for permanent reset"
Canoni850, i950, S600
Start with the printer OFF
1. Hold down RESUME and then hold down POWER
2. release RESUME
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses - light color - function
Number of presses - light color - function 0 presses - green- Test print (or exit service mode on i960)1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960) 2 presses - green - EEPROM initialize 3 presses - orange- Reset waste ink counter
Canon i320, i255 Waste Ink Counter Reset.
Canon i320, i255 Waste Ink Counter Reset.
Step 1 : Manual for service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.or
Step 1: Manual for service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.
Step 2 : Softwarefor Permanent
1. Reconnect the printer cable.
2. OpenGeneral Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.
Remark"After service mode Pls use software for permanent reset"
Canon Printer Waste Tank Reset
CanonGENERIC "S"SERIES RESET CODE
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWERbutton.
(3) Release the RESUME button, Next press and release the RESUME button two (2) more times in succession. Note: you are still holding the POWER button). The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test print out, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to"set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.
Reset Waste Ink Canon IP1500
Step 1 Manual for Service mode to reset waste ink or blinking canon ip1500
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
Step 2 Use software for Permanent to reset waste ink
download tool to reset permanent waste ink.
this resetter printer Canon IP 1500. This tool can reset waste ink for canon ip1500 permanent
User guide:
1.
Unzip downloaded file.
2.
Run GeneralTool.exe
3.
Select the connected USB port number from USB port
4.
Click LOCK RELEASE, and select the applicable model name in SET DESTINATION
5.
In CLEAR WASTE INK COUNTER, select MAIN or PLATEN. The selected waste ink counter will be reset. MAIN resets the main waste ink counter, PLATEN resets the platen waste ink counter.
If both the main and platen waste ink absorbers are replaced, reset both the main and platen waste ink counters.
http://www.savefile.com/files/1039880
http://soulved.blogspot.com
Service Manual 700/750C/750C PLUS/755CM Hp Designjet Plotters
This service manual contains information necessary to test, calibrate and service:
1. HP Designjet 700 plotters (models C4705A and C4706A)
2. HP Designjet 750C plotters (models C3195A and C3196A)
3. HP Designjet 750C Plus plotters (models C4708A and C4709A)
4. HP Designjet 755CM printers (models C3198A and C3198B)
For information about these plotters/printers, refer to the corresponding user and quick-reference guide
Table of contents HP Designjet 700/750C/750C PLUS/755CM Printer Service And Repair Manual
* Product Information
* Site Planning and Requirements
* Installation and Configuration
* Preventive Maintenance
* Functional Overview
* Removal and Replacement
* Calibrations and Adjustments
* Troubleshooting
* Print Quality
* Product History and Service Notes
* Parts and Diagrams
* Support Services
http://rapidshare.com/files/108116030/HP_DESIGNJET_700__750C__750CT__755CM_Service_Manual.rar
Oki c5300n drum resetting
Turn off the printer
Turn the printer on whilst holding down Menu button. (Display says user maintenance.)
Press the menu button three times. (The display will say drum counter reset.)
Press enter key. The system should go back on line, if not press on-line key.
Error 6A00 on Canon PIXMA MP800
The 6A00 is a Canon generic code for paper path jam. Some where in the paper path a sensor is activated indicating paper jam so the printer will give off a 6A00 code. As a Canon tech, I usually find the code, almost 90% of the time, is related to the purge unit being jammed with something and not being able to move. Moving the print head assembly will not clear a purge unit if its jammed with paper, paper clips, push pins, screws, cookie crisp, flower bud pods or the like. And yes I have found all those things in a purge unit. The offending item needs to be removed or the purge unit needs replacement. A Pixma MP830 would still be under Canon warranty, get it into a shop and save yourself the hassel.
Incidently, the 6A00 error pertains to all Canon printers made in the last several years, its not just used in one model. And its always a paper path error or purge unit.
I forget myself so here goes, the purge unit, called a spittoon assembly in an HP, lexmark, and other inkjet printers, is where the print head assembly parks when not in use, also its other job is to clean and make sure the print head is clean and open for printing. That is why you'll find the print head assembly parked on top of it. It also has a an electrical pump to milk the print heads and test for ink flow.
Subscribe to:
Posts (Atom)